There are a number of methods how to hang acoustic foam without damaging walls but here we will describe the best method of how to hang acoustic foam without damaging walls.
Which are those methods that can help to hang acoustic foam to the walls?
The methods how to hang acoustic foam without damaging walls are as follows,
- Double-sided adhesive square
- T shaped push pins
- 3M Command strips
- Liquid nails
- Double-sided velcro
- 3M general purpose 45 adhesive spray
- Combination of 3M command strips and One-sided velcro
These all are the methods that you can use to hang acoustic foam to your walls. Now here we will choose one of the best methods among them and will discuss that particular method only here.
How To Hang Acoustic Foam Without Damaging Walls: By Using Combination Of Velcro & Command Strips
There are a number of methods to control the sound of a room and one of the most common methods is acoustic foam. Acoustic foam is affordable as well as readily available in different colors.
Acoustic foam is used to absorb sounds so that it could stop the echoes and reverberation. But it can only do this when its installation is correct.
If it isn’t installed perfectly then it does not absorb the noise and simply bounces it back and can ruin recording but if you follow these steps given here then you would definitely hang acoustic panels without damaging the walls and it will also work well.
There are different ways to install the acoustic foam, you can use push pins, liquid nails, adhesive spray. However, all these methods can cause damage to your walls and that’s why we came here with this method.
This method is the combination of Command strip and Velcro. If you follow the given steps then I assure you that this method won’t damage your walls as well as your acoustic foam.
Step 1. Which Things Do You Need To Hang The Acoustic Panel
It is the necessary step of this method, without this you can not move ahead, so pick the materials first which we mentioned below and place those materials in a room where you have to hang the acoustic panel,
- Acoustic foam
- One-sided Velcro
- 3M Command strips
- Measurement tape
- Cutter or Electric carving knife (if required)
- Scissor
- Damp cloth
Step 2. Decide The Location Where Do You Have To Place The Acoustic Panels
Now you have to decide the location where you have to hang the acoustic panel.
As we recommend if you are a music lover then always hang the acoustic panel on that wall which is in front in the direction of the speaker or music system and then hang it on the backside of the wall of the speaker.
These two walls are very very important and then after you can also hang it on the rest of the walls if you required.
Also, hang the acoustic panel in the middle of the height of the wall in such a way that the center of the acoustic foam panel lies in between the middle of the height of the wall or roughly eye level for a smaller frame.
Step 3. Clean The Required Area Of Your Wall
Clean the area of your wall with the help of damp cloths and make the area dust, dirt, oil, and grease-free. Remember do not use any household cleaner, it may reduce the adhesion of the command strips.
For hanging acoustic foam, do not use the area where the paint is peeling off and uneven surface. Make sure the wall where you are hanging acoustic foam that wall should be primer proof.
Step 4. Measuring & Cutting The Acoustic Foam
Measure the acoustic foam and transfer this measurement onto the wall where you have to hang the acoustic foam. If the acoustic foam is more in length or in height then you can cut it with the cutter or electric carving knife.
But we always recommend the free space for the installation of acoustic foam so that you do not need to be cut the foam. So always use the space which is free from any hurdles like switches, boards, hooks, etc.
Step 5. Installation Of Acoustic Foam
Take Velcro out of the box and cut out into small pieces approximately 1 inch.
Peel off the plastic backing of the Velcro and then just stick it in the center of the top of the backside of the acoustic foam panel and press it gently so that it sticks well.
Now peel off the plastic backing of the command strip and then just stick it over the velcro, now you do the same for all your acoustic foam panels.
Gather everyone in one place, take one of them and remove the plastic backing of the command strip. Now stick it to to your wall where you did already marking and press it gently so that it sticks well.
In this way you can hang all your panels by your own. Hope you have got the answer of your question “how to hang acoustic foam without damaging walls”
If you feel one of your foam panels not placed properly then you can remove the foam panel very easily without damaging walls for that only you have to hold the Velcro from the bottom and pulling it with the Velcro.
Then you find the command strip is still up there, now you can replace this or you can fix it up.
Hope this article “how to hang acoustic foam without damaging walls” will help you in the right direction.